Do It Yourself Bathtub Installation.

Pest Control

This great article following next about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is really captivating. Don't overlook it.


How to Install a Bathtub Yourself
Mounting a tub isn't specifically rocket science, however it does call for strong plumbing, carpentry, and often, tiling abilities. Changing an old tub with a brand-new one is also a moderately tough task. If the old bathtub is conveniently available, the project can move immediately; if you need to open up a wall to eliminate the old bathtub and also place the brand-new bathtub, the task is much harder. In either case, the job is within a house handyman's skills, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. See to it you have actually certified yourself for the task as well as are comfortable attempting it. Instead of hiring a professional to take over a halfway-completed job, it is much better to think about utilizing one before you begin. Chances are you may need a professional plumber to make tube connections.
This article will certainly aid you set up a brand-new tub in your restroom if you have already bought a new bathtub and do not require to alter the plan of your previous supply of water pipes.
Your devices and also product checklist ought to comprise the following:
  • New Bathtub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Removing Old Touches


    If you need to replace old taps with brand-new ones as a part of your setup, then the first thing you should do is disconnect the water. After doing so, activate the taps to drain any kind of water continuing to be in the system. The procedure of removing the existing taps can be fairly troublesome due to the restricted accessibility that is commonly the situation.
    Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the remaining water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
    Prior to proceeding to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.

    Fitting New Taps


    If the tails of the new faucets are plastic, then you will certainly need a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end provides a link to the existing supply pipelines.
    If you need to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
    Next off, position the tap in the installing hole in the bath/basin making certain that the washers remain in place in between the faucet as well as the sink. Protect the faucet in position with the supplier given backnut. When the faucet is securely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former type must be connected to the tap finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.

    Installing the Tub


    Making use of the two wooden boards under its feet, put the bath tub in the required position. The wood boards are helpful in evenly spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 tiny factors.
    The next goal is to make sure that the bath tub is leveled all round. This can be accomplished by examining the level and changing the feet on the tub till the level reads level.
    To set up taps, fit all-time low of the outermost adaptable tap connector to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other tap.
    Switch on the supply of water as well as inspect all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill the bath tub as well as also check the overflow outlet as well as the regular electrical outlet for leaks.
    Finally, take care of the bath paneling as explained in the supplier's user's manual. Tiling and sealing around the tub must wait up until the bath tub has actually been made use of a minimum of when as this will certainly resolve it right into its last position.

    Preparing for the Installation


    Firstly, the supporting frame supplied with the bath ought to be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to make certain that if the faucet features a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets device to avoid stress on the bathtub.
    Fit the flexible faucet adapters to the bottom of the two taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the provided washing machines.
    Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be fitted in its last position.

    Tiling Around the Bath tub


    In the location where the bath fulfills the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to break an inflexible seal, creating the water to permeate the wall surface between the bathroom as well as the tiling, resulting in complications with moisture and feasible leaks to the ceiling listed below.
    You can choose from a selection of coloured sealers to assimilate your fixtures and installations. They are sold in tubes as well as cartridges, and are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill the bath tub with water prior to sealing, to enable the movement experienced when the bathtub is in usage. The sealer can break rather early if you do not take into consideration this movement before securing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    A Step-by-Step Guide to Installing a Bathtub

    As a keen person who reads about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I assumed sharing that excerpt was really useful. Remember to take a moment to share this write-up if you enjoyed it. We love reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.



    Schedule Service

    Leave a Reply

    Your email address will not be published. Required fields are marked *